HTL10 SM
HTL10 SM waterborne self-sealing lacquer, 30 gloss (satin)
One-pack waterborne self-sealing clear (lacquer and sealer in one), formerly sold as HTL20 SM. Very clear, non-yellowing, fast drying, high solids, good price/quality ratio. Solvent-free, so it can be used on children's furniture and toys.
- Interior furniture doors and panels in any wood species
- Children's furniture and toys
- Pale woods where non-yellowing matters
Mix calculator
Ratio 100 : 0.0
| Component | Weigh out |
|---|---|
| HTL10 SMpart A | 500 g |
| Water (demineralised)Thinner | 0.0 g |
| Total | 500 g |
Covers roughly 4.76 m² at 105 g/m².
Pot life of the mix: n/a (1K).
Ask about HTL10 SM
Answers are based on the HTL10 SM data and the products it mixes with.
Mixing matrix
- Water (demineralised)Thinner% by weight: 0–10 %official% by volume: 0–10 %official
Only if viscosity is a problem for spraying (heat, small tip). Normally sprayed as supplied.
Demineralised/distilled water only, never hard tap water. Do not exceed 10 %.
- Water (demineralised)Thinner% by weight: 0–10 %catalog
2025-2026 catalog family card: water 0–10 % (basis not stated).
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | Water (demineralised) | 0–10 %official | 0–10 %official | Only if viscosity is a problem for spraying (heat, small tip). Normally sprayed as supplied.Demineralised/distilled water only, never hard tap water. Do not exceed 10 %. |
| Thinner | Water (demineralised) | 0–10 %catalog | — | 2025-2026 catalog family card: water 0–10 % (basis not stated). |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 32 ± 1 %dealer
- Solids, catalogue %
- 32 %catalog
- Viscosity
- 45 ± 5 sdealer
- Density
- ≈1.03 g/cm³recommended
- Gloss
- 30 ± 3 GUdealer
- Pot life
- n/a (1K)recommended
- Drying · Touch-dry
- 30 mindealer
- Drying · Sand or stack
- 4 hdealer
- Drying · Full cure
- 8 hdealer
- Drying · Conditions
- 20 °C
- Lightfastness
- excellent non-yellowingofficial
- Thixotropy
- norecommended
Colours
- HTL10 SM · clear
Application
HVLP
- Nozzle
- 1.5–1.7 mmrecommended
- Pressure · fluid
- gravity cup / 0.8–1.2 bar if pressure potrecommended
- Pressure · air
- 1.8–2.2 barrecommended
- Spray viscosity
- 45 ± 5 sdealer
- Target spray viscosity
- 25–35 srecommended
- Consumption · Coat 1
- 90–100 g/m²official
- Consumption · Coat 2
- 100–120 g/m²official
- Consumption · Total range
- 90–120 g/m²dealer
- Wet film
- 85–120 µmrecommended
- Coats
- 2 (1st 90–100, 2nd 100–120 g/m²)official
- Flash-off
- 10–20 minrecommended
- Gun distance
- 15–20 cmrecommended
- Overlap
- 50–75 %recommended
Lay it on as an even wet coat, don't dust it — dry-sprayed waterborne goes orange-peel and cloudy. Don't overload: 120 g/m² per pass max. Stainless gear, flush with water before and after.
Conventional spray
- Nozzle
- 1.4–1.6 mmrecommended
- Pressure · air
- 2.5–3.5 barrecommended
- Consumption · Coat 1
- 90–100 g/m²official
- Consumption · Coat 2
- 100–120 g/m²official
- Consumption · Total range
- 90–120 g/m²dealer
Official method is plain air spray. Transfer efficiency up to ~40 % (methods page).
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.28 mmrecommended
- Pressure · fluid
- 10–40 barrecommended
- Pressure · air
- 1–2 barofficial
- Consumption · Coat 1
- 90–100 g/m²official
- Consumption · Coat 2
- 100–120 g/m²official
- Consumption · Total range
- 90–120 g/m²dealer
Pump and hoses must be waterborne-rated (stainless).
Brush
- Consumption
- 90–120 g/m²catalog
Synthetic brush, lay off in one direction, don't overwork — it skins fast.
Process and compatibility
- Substrate preparation
- Sanded clean wood/veneer/MDF, dust off. Stain with CPH series (60–80 g/m²), dry 2–4 h before the first coat.dealer
- Goes over
- bare wood (self-sealing) / CPH stains
- Sanding · Between coats
- P240–P280 after 4 hdealer
- Sanding · Final
- do not sand the final coatrecommended
- Temperature and humidity
- > 15 °C, RH < 70 %dealer
- Ideal temperature and RH
- 18–25 °C, RH 50–65 %, good air movementrecommended
- Don'ts
- Don't apply below 15 °C or above 70 % RH.
- Don't thin more than 10 % or with hard water.
- Don't mix with solvent thinners (S50/S80 etc.) or with 2K acrylic/PU.
- Don't flood a thick coat in one pass.
- Don't let the can freeze.
Storage
- Storage temperature
- 5–30 °Crecommended
- Packaging
- 1 kg,5 kg,10 kgdealer
Safety: Solvent-free — suitable for children's furniture and toys (catalog 2022/dealer; the 2025-26 catalog mentions children's furniture only). When spraying wear a particulate mask (P2) and ventilate.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer HTL10 SM: 'прежнее наименование HTL20 SM'; gloss 30±3, solids A 32±1 %, visc A 45±5 s VZ-4 @20 °C, touch 30 min, full 8 h; spray 90–120 g/m²; >15 °C, RH<70 %; demineralised water, ≤10 %; mix well, flush gear with water; packs 1/5/10 kg
- dealer search: only HTL10 SM listed
- official page: properties, coats 90–100/100–120 g/m², water 0–10 % w/v
- legacy official page HTL20030 (old name)
- 2022 catalog: HTL20 SM 32 %, 0–10 % water, 90–120 g/m²
- dealer HTL20 G (sibling gloss variant): 80 ± 3 GU, visc 27 ± 5 s VZ-4, touch 30 min, full 8 h; schedule CPH stain 60–80 g/m² → 2–4 h → HTL20 G 100 g/m² → 4 h → P240–P280 → HTL20 G 120 g/m² → 8 h; text mentions HTL10 G 70 GU
- application methods page
- dealer HTL20 SM page (former name; HTL20030 alias)
- 2019 catalog text: HTL20 M (20 гл) / HTL20 SM (30 гл) Лак/грунт ВР прозрачный, 32 %, water 5–10 %
Not covered by the sources
- no official t-color.ru page under the HTL10 SM code (official data taken from the HTL20 SM page = former name)
- density (only derived)
- dust-free time
- hardness / chemical resistance / elasticity values
- shelf life
- pot life n/a (1K) — not stated explicitly
- no Technocolor TDS PDF found (web search budget exhausted this session; earlier HTL20 search found none)
- not used in any official finishing schedule (information/technology)
- gloss sibling: dealer HTL20 G page (80 ± 3 GU, 27 ± 5 s VZ-4) mentions 'HTL10 G … 70 глосс' in its marketing text, but dealer search for HTL10 returns only HTL10 SM — HTL10 G figures unconfirmed
- 2025-26 catalog lists HTL20 G as 60 GU, dealer HTL20 G page says 80 ± 3 GU — sibling gloss level inconsistent across sources