HPL60 SM
HPL60 SM waterborne white exterior enamel (30 gloss) / white waterborne exterior tinting base
One-pack waterborne (acrylic) white semi-matt exterior enamel, also sold as the white waterborne converter for tinting pastel-shade enamels. Elastic — won't crack with temperature swings — and stands up well to rain, snow and UV. Good hiding power, covers minor defects. Practically odourless, no organic solvents. Spray or brush.
- timber house facades
- exterior doors and windows
- decks/terraces, gazebos, fences
- garden furniture
- tinting pastel-shade exterior enamels (as a converter)
Mix calculator
Ratio 100 : 5.0
| Component | Weigh out |
|---|---|
| HPL60 SMpart A | 476 g |
| waterThinner | 23.8 g |
| Total | 500 g |
Covers roughly 3.70 m² at 135 g/m².
Ask about HPL60 SM
Answers are based on the HPL60 SM data and the products it mixes with.
Mixing matrix
- waterThinner% by weight: 0–10 %catalog% by volume: 0–10 %dealer
Brush — 0–5 %; spray gun — 5–10 % to working viscosity.
Clean water only (demineralised is best). Never use S50/S80 solvent thinners.
- CH 10 / CH 20 / CH 21 / CH 22 / CH 23 / CH 30 / CH 40 / CH 50 / CH 51 / CH 53 / CH 60 / CH 70 / CH 80 / CH 90 / CH 91Additive
Tinting to RAL/NCS; per the catalog HPL60 SM is the base for pastel shades (bright/deep shades go on the clear base HTL60 SM).
CH pastes are the waterborne series (list from the tinting leaflet). Dose per the formula; keep paste under ~5 % for pastels (derived).
| Role | Material | % by weight | % by volume | When |
|---|---|---|---|---|
| Thinner | water | 0–10 %catalog | 0–10 %dealer | Brush — 0–5 %; spray gun — 5–10 % to working viscosity.Clean water only (demineralised is best). Never use S50/S80 solvent thinners. |
| Additive | CH 10 / CH 20 / CH 21 / CH 22 / CH 23 / CH 30 / CH 40 / CH 50 / CH 51 / CH 53 / CH 60 / CH 70 / CH 80 / CH 90 / CH 91 | — | — | Tinting to RAL/NCS; per the catalog HPL60 SM is the base for pastel shades (bright/deep shades go on the clear base HTL60 SM).CH pastes are the waterborne series (list from the tinting leaflet). Dose per the formula; keep paste under ~5 % for pastels (derived). |
Percentages are per 100 parts of component A.
Characteristics
- Solids
- 52 ± 1 %dealer
- Viscosity
- 8 ± 1 sdealer
- Gloss
- 30 ± 3 gloss units (angle not stated; 60° assumed)dealer
- Drying · Dust-free
- 15–20 minrecommended
- Drying · Touch-dry
- 30 mindealer
- Drying · Sand or stack
- 3–4 hrecommended
- Drying · Full cure
- 24 hdealer
- Drying · Conditions
- 20 °C
- Elasticity
- elastic — won't crack with temperature swingsofficial
- Weather resistance
- good weather resistance (rain, snow, UV)official
- Hiding power
- high hiding power, hides minor defectsdealer
- Odour / VOC
- waterborne, no harmful solvents, practically odourlessdealer
Colours
- HPL60 SM (белая база) · white; base for pastel RAL/NCS shades tinted with CH pastes
Application
HVLP
- Consumption
- 120–150 g/m²official
- Nozzle
- 1.7–2 mmrecommended
- Pressure · air
- 2–2.5 barrecommended
- Spray viscosity
- 5–10 % water addedrecommended
- Wet film
- 85–120 µmrecommended
- Coats
- 2 coatsrecommended
- Flash-off
- 15–30 minrecommended
- Recoat
- 3–4 hrecommended
- Sanding between coats
- P320–P400 light denib after the first coatrecommended
- Dry film
- 35–50 µmrecommended
15–20 cm distance, 50 % overlap, fan fully open. Flush the gun with water before and after (dealer).
Conventional spray
- Consumption
- 120–150 g/m²official
- Nozzle
- 1.8–2.2 mmrecommended
- Pressure · air
- 3–4 barrecommended
- Spray viscosity
- 5–10 % water addedrecommended
- Coats
- 2 coatsrecommended
Transfer efficiency up to 40 % (official methods page) — actual usage is higher.
Airmix (air-assisted airless)
- Nozzle
- 0.23–0.33 mmrecommended
- Pressure · fluid
- 40–80 barrecommended
- Pressure · air
- 1–2 barofficial
- Spray viscosity
- 0–5 % water addedrecommended
- Coats
- 2 coatsrecommended
Best choice for production windows/doors: air-spray quality, higher throughput.
Airless
- Nozzle
- 0.28–0.38 mmrecommended
- Pressure · fluid
- 120–180 barrecommended
- Spray viscosity
- 0–5 % water addedrecommended
- Coats
- 2 coatsrecommended
For big areas — facades, fences. Finish quality on joinery is below Airmix.
Brush
- Consumption
- 120–150 g/m²official
- Spray viscosity
- 0–5 % water addedrecommended
- Coats
- 2–3 coatsrecommended
- Recoat
- 3–4 hrecommended
Synthetic brush for waterborne paints; lay off along the grain, don't work a drying edge.
Process and compatibility
- Substrate preparation · Wood moisture
- 8–14 %official
- Substrate preparation · Preparation
- Dry, clean, dust-free wood; sand P150–P180 (end-grain P180–P220); remove resinous knots and any flaking old finish.recommended
- Sister products
- HTL60 SM,HTL61 SM,HTS30catalog
- Sanding
- Between coats P320–P400 after the first coat; do not sand the finish coat.recommended
- Temperature and humidity
- Apply above +15 °C and below 70 % RHdealer
- Don'ts
- don't apply below +15 °C or above 70 % RH (dealer)
- don't thin with S50/S80 solvents — water only
- don't paint wet wood, before rain or in direct sun (derived)
- don't let it freeze (derived)
- don't apply over oil/wax finishes without stripping (derived)
- Equipment cleaning
- Flush equipment with water before and after usedealer
Storage
- Packaging
- 1,5,10 kgdealer
- Storage temperature
- 5–30 °Crecommended
Safety: Waterborne, no organic solvents, practically odourless (dealer). Wear gloves and a particulate mask when spraying; don't pour down the drain (derived — no SDS published).
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- official page: name, properties (elastic, weather resistant), spray/brush 120–150 g/m²
- t-colormarket.ru (re-checked 2026-10-05): gloss 30±3, solids part A 52±1 %, viscosity part A 8±1 s CF-8 at 20 °C, touch dry 30 min, full dry 24 h, apply >15 °C / <70 % RH, flush equipment with water, spray/brush 120–150 g/m², 1/5/10 kg, 1 011 ₽/kg под заказ; no thinner table
- woodonline.ru (re-checked 2026-10-05): gloss 30±3, solids 52±1 %, 8±1 s CF-8, touch 30 min, full 24 h, pigmented, waterborne; 'Разбавляется водой в пропорции 0-10/0-10'; systems: facades, doors; ТДС on request
- official news 'Серия HPL' (26.02.2026): tint to RAL/NCS with CH pastes, high elasticity, weather/UV resistance, spray or brush
- official application methods page
- official glossary: wood moisture 8–14 %, RH 40–75 %
- official characteristics page: Ford cup orifices 2/4/6/8 mm (basis for CF-8 = 8 mm cup)
Not covered by the sources
- No Technocolor ТДС/technical data sheet PDF for HPL60 SM found online (woodonline: ТДС 'по запросу')
- density not published (derived value used)
- dust-free and recoat/sand times not published (derived)
- spray viscosity of the thinned mix not published
- hardness, chemical resistance, abrasion, lightfastness rating (numeric) not published
- maximum CH paste loading / tinting formulas not published
- recommended primer/impregnation under HPL60 SM not officially stated (derived)
- shelf life not published
- not used in any official finishing schedule (information/technology)
- one unverifiable search snippet (Kazakh dealer, page dead) claimed thixotropy and 0–5 % water — not used
- t-colormarket.ru shows no hardener/thinner table for HPL60 SM; the water 0–10 % figure comes from the catalog and woodonline only
- gloss measuring angle not stated (assumed 60°)
- volume solids not published; dry-film estimates are derived