ATL70 UM
Acrylic touch-up lacquer, ultra-matt (10 GU), 400 ml aerosol can
Acrylic lacquer in a spray can for repair and touch-up work: range of sheens, very clear, non-yellowing, fast drying. Ready to use. Comes with 2 actuator caps — one for halo-free blending, one for straight coating.
- Any wood species
- Lacquering small areas
- Restoring the finish after a repair
- Matching sheen on a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about ATL70 UM
Answers are based on the ATL70 UM data and the products it mixes with.
Characteristics
- Gloss
- 10 GU (глосс; угол измерения не указан / measuring angle not stated)dealer
- Drying · Touch-dry
- 10–20dealer
- Drying · Full cure
- 3–4dealer
- Drying · Conditions
- 20 °C
- Volume
- 400 mldealer
- Components
- ready to use (1K)dealer
- Yellowing resistance
- non-yellowingdealer
Colours
- прозрачный · Clear
Application
Aerosol
- Method (fallback)
- conventional_spray
- Consumption
- 80–100dealer
- Gun distance
- 15–25dealer
- Nozzle
- not adjustable — 2 supplied actuators (halo-free for blending, standard for straight coating)recommended
- Pressure
- не регулируется (давление баллона) / not adjustable (can pressure); греть баллон до комнатной ~20 °C / bring the can to room temperature ~20 °Crecommended
- Sanding between coats
- don't sand between coats; for dust nibs wait 3–4 h, denib with P800–P1000 or a grey pad and re-sprayrecommended
- Technique
- Shake well (1–2 min after the ball starts rattling), keep the can upright, move at an even pace, start and stop off the part, ~50 % overlap. To blend into old finish use the halo-free cap and a light misting last pass over the repair edge. Match sheen to the surrounding finish: 5 GU around it → ATL70 DM, 20 GU → ATL70 M.recommended
Shake the can before use. Don't spray onto cold or hot surfaces. Spray from 15–25 cm. After use, turn the can upside down and spray until the nozzle runs clear. dealer
Process and compatibility
- Substrate preparation
- Fill the repair (wax, filler, CTU touch-up marker), sand P320–P400, key the surrounding old finish with P600–P800 or a grey pad, de-dust and degrease. On a larger bare-wood area seal with a primer first.recommended
- Sanding
- don't sand or polish the finished matt coatrecommended
- Don'ts
- Don't spray onto cold or hot surfaces
- Don't skip shaking the can
- Don't put the can away without clearing the nozzle
Storage
- Packaging
- 400 ml aerosol can + 2 capsdealer
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- описание, свойства, применение, расход 80–100 г/м², дистанция 15–25 см, блеск 10 гл, на ощупь 10–20 мин, полная сушка 3–4 ч, 400 мл
- состав линейки у дилера: ATL70 DM (5), UM (10), M (20), SM (30), G (75 гл); SG у дилера не найден
Not covered by the sources
- solids_pct (не опубликовано)
- viscosity (к аэрозолю неприменимо / not published)
- density
- dust_free_min
- stack_or_sand_h
- hardness, lightfastness, chemical_resistance, elasticity
- shelf_life
- official SDS/TDS — не найден
- wet_film_um
- расхождение по расходу: дилер 80–100 г/м², каталог 2025–2026 — 150 г/м²
- не входит ни в одну официальную технологию отделки
- расхождение по блеску G: листовка 70 гл, каталог/дилер 75 гл (к UM не относится)