ATL70 G
Acrylic touch-up lacquer, gloss (75 GU), 400 ml aerosol can
Acrylic lacquer in a spray can for repair and touch-up work: very clear, non-yellowing, fast drying. Ready to use, sprays without a halo and lays down evenly. Comes with 2 actuator caps — one for halo-free blending, one for straight coating.
- Any wood species
- Lacquering small areas
- Restoring the finish after a repair
- Matching sheen on a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about ATL70 G
Answers are based on the ATL70 G data and the products it mixes with.
Characteristics
- Gloss
- 75 GU (глосс)dealer
- Lightfastness
- non-yellowingdealer
- Drying · Touch-dry
- 10–20dealer
- Drying · Full cure
- 3–4dealer
- Drying · Conditions
- 20 °C
- Volume
- 400 mldealer
- Components
- ready to use, nothing added (i.e. effectively 1K)catalog
Colours
- прозрачный · Clear
Application
Aerosol
- Method (fallback)
- conventional_spray
- Consumption
- 80–100dealer
- Gun distance
- 15–25dealer
- Nozzle
- not adjustable — 2 supplied actuators (halo-free for blending, standard for straight coating)recommended
- Pressure
- not adjustable (can pressure); bring the can to room temperature ~20 °Crecommended
- Sanding between coats
- don't sand between coats; for dust nibs wait 3–4 h and denib at P800–P1200recommended
- Technique
- Keep the can upright, move at an even pace, start and stop the spray off the part, ~50 % overlap. To blend into old finish use the halo-free cap and a light misting last pass over the repair edge.recommended
Shake the can before use. Don't spray onto cold or hot surfaces. Spray from 15–25 cm. When done, turn the can upside down and spray until the nozzle runs clear. dealer
Process and compatibility
- Substrate preparation
- Fix the defect (wax/filler/CTU touch-up marker), sand P320–P400, key the surrounding old finish with P600–P800 or a grey pad, de-dust and degrease. Seal bare wood with a primer first.recommended
- Sanding
- don't sand or polish the final gloss coat unless you mustrecommended
- Don'ts
- Don't spray onto cold or hot surfaces
- Don't skip shaking the can
- Don't put the can away without clearing the nozzle
Storage
- Packaging
- 400 ml aerosol can + 2 capsdealer
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- описание, свойства, применение, расход 80–100 г/м², дистанция 15–25 см, 75 гл, на ощупь 10–20 мин, полное 3–4 ч, 400 мл
- состав линейки ATL70 (DM/UM/M/SM/SG/G), одинаковые данные сушки у сестринских позиций
Not covered by the sources
- solids_pct (не опубликовано)
- viscosity (для аэрозоля не применимо / not published)
- density
- dust_free_min
- stack_or_sand_h
- hardness, chemical_resistance, elasticity
- shelf_life
- gloss: листовка 70 гл vs дилер/каталог 2025 75 гл
- consumption: каталог 150 г/м² vs дилер 80–100 г/м²
- official SDS/TDS — бюджет веб-поиска исчерпан, ТДС не найден
- wet_film_um
- не используется ни в одной официальной схеме отделки (information/technology)