APL70 UM
Acrylic touch-up enamel, white, aerosol can (10 gloss)
Ready-to-use acrylic enamel in an aerosol can for touch-up and restoration work: high hiding power, rich colour, fast drying, no overspray halo. Comes with two actuator caps — a no-halo cap for spot repairs and blending, and a wider cap for first-coat painting.
- Any wood species
- First finish on small areas
- Re-coating after defect repair (chips, dents, scratches filled with putty/wax)
- Evening out sheen after a repair on white matt fronts
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 UM
Answers are based on the APL70 UM data and the products it mixes with.
Characteristics
- Gloss
- 10 GU 60°dealer
- Drying · Full cure
- 3–4 hdealer
- Drying · Dust-free
- 10–15 minrecommended
- Drying · Touch-dry
- 20–30 minrecommended
- Drying · Conditions
- 20 °C
- Pot life
- n/a — one-component aerosol, no mixingdealer
Colours
- white · White
Application
Aerosol
- Device
- aerosol can (2 interchangeable actuator caps)
- Nozzle
- built-in actuator (~0.3–0.5 mm orifice equivalent); use the no-halo cap for spot repair/blending, the wide-fan cap for first coatsrecommended
- Pressure · fluid
- not adjustable — can internal pressure (typically ~3–5 bar at 20 °C)recommended
- Pressure · air
- n/arecommended
- Gun distance
- 15–25dealer
- Consumption
- 80–100 g/m²dealer
- Coats
- 2–3 thin crossing passesrecommended
- Recoat
- 10–20 min between passes; next day for sanding/overcoating with other productsrecommended
- Sanding between coats
- Not needed between aerosol passes; if dust nibs, denib after full dry (≥ 3–4 h) with P600–P800 / grey pad, then a final light passrecommended
Shake the can before use. Do not spray onto cold/hot surfaces. Apply from 15–25 cm. After work turn the can upside down and blow the nozzle clear (until only clear gas comes out). dealer
Process and compatibility
- Substrate preparation
- Surface clean, dry and degreased. Level the repaired spot (filler, wax), sand P320–P400, de-dust. Scuff the surrounding old finish lightly with a grey pad so the touch-up keys in.recommended
- Don'ts
- Do not spray onto cold or hot surfaces
- Do not add hardener or thinner
- Do not sand or polish the final 10-gloss coat — it burnishes to shiny patches
- Do not lay it on heavy — sags and blotchy sheen
Storage
- Packaging
- 400 мл аэрозольный баллонdealer
- Storage temperature
- 5–25 °C, away from heat and sun, never above 50 °Crecommended
Safety: Pressurized, flammable aerosol. Do not heat above 50 °C, pierce or burn, even when empty. Use with ventilation and an organic-vapour (A) respirator; keep away from flames and sparks.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: description, properties, uses, 80–100 g/m², 15–25 cm, gloss 10, full dry 3–4 h @20 °C, 400 ml, white, price
- sibling codes APL70 M/SM/G and ready RAL versions R1015 M/SM, R9001 M, R9003 M, R9010 M, R9016 M (same spec text, different gloss/colour); re-checked 2026-10-05
Not covered by the sources
- No official t-color.ru product page and no TDS/SDS found (web-search budget exhausted; none in local sources)
- Solids, viscosity, density not published (not meaningful for a ready aerosol, but unknown)
- Dust-free / touch / recoat times not published (only full dry 3–4 h)
- Consumption conflict: catalog 150 g/m² vs dealer 80–100 g/m²
- Shelf life and storage temperature not published
- Compatibility over/under other Technocolor systems not stated by manufacturer
- No finishing schedule (information/technology) uses APL70
- Hardness, lightfastness, chemical resistance not published