APL70 SM
Acrylic enamel, white, 30 gloss (semi-matt), 400 ml aerosol can
White acrylic enamel in an aerosol can for touch-up and restoration: high hiding power, rich colour, 30-gloss semi-matt sheen, fast drying. Ready to use. Comes with two spray tips — one for halo-free spotting/blending and one for full-coverage first painting.
- any wood species
- first finishing of small surfaces
- refinishing an area after a defect has been repaired (chips, dents, scratches)
- evening out the sheen over a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 SM
Answers are based on the APL70 SM data and the products it mixes with.
Characteristics
- Gloss
- 30 GU 60°dealer
- Drying · Touch-dry
- 10–20 mindealer
- Drying · Full cure
- 3–4 hdealer
- Drying · Conditions
- 20 °C
- Volume (ml)
- 400dealer
- Pot life
- n/a — 1K aerosolrecommended
- Binder
- thermoplastic 1K acrylic resin, TiO2 white pigmentrecommended
- Lightfastness
- good — acrylic binder is non-yellowing; no figure publishedrecommended
- Chemical resistance
- lower than 2K systems; not for worktops/heavy-wipe zonesrecommended
Colours
- APL70 SM · white
- APL70 R1015 SM · light ivory
- (под заказ / to order) · any colour to order, minimum batch 24 cans
Application
Conventional spray
- Device
- aerosol can with two interchangeable tipsdealer
- Pressure · air
- n/arecommended
- Gun distance
- 15–25 cmdealer
- Consumption
- 80–100 g/m²dealer
- Technique
- Shake the can well (at least 1–2 min after the ball starts rattling). Test spray on card. Keep the can parallel to the surface, start and stop off the edge, ~50 % overlap. For spot repairs use the halo-free tip and feather the edge from further away (20–25 cm). When done, turn the can upside down and spray until only gas comes out.recommended
Shake before use; do not spray onto cold or hot surfaces; keep 15–25 cm away; after work, invert and purge the nozzle. dealer
Process and compatibility
- Substrate preparation
- Repair area: filler/primer fully dry, sanded P320–P400; surrounding cured 2K finish scuffed P400–P600 or grey Scotch-Brite, dusted and degreased. On bare wood prime first (e.g. the shop's white primer) or raised grain and absorption will show as sheen patches.recommended
- Don'ts
- spray onto cold or hot surfaces
- lay it on in one heavy coat
- sand or polish the final 30-gloss coat
- put the can away without purging the nozzle
- heat the can with open flame or above 50 °C
Storage
- Packaging
- 400 ml candealer
Safety: Pressurised container with flammable contents: don't heat, pierce or spray near flame. Use in a ventilated area or spray booth, with an organic-vapour respirator (A2P2) and gloves.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer page APL70 SM: description, properties, use, 80–100 g/m², 15–25 cm, 30 gloss, touch 10–20 min, full dry 3–4 h at 20 °C, 400 ml, price
- APL70 R1015 SM colour variant: same 30 gloss, full dry 3–4 h, 80–100 g/m², 400 ml, 821 ₽; no touch-dry figure listed
- sibling APL70 M (20 gloss), identical spec otherwise
- sibling APL70 G (70 gloss)
- sibling APL70 UM (10 gloss)
Not covered by the sources
- official product page / TDS / SDS not found (t-color.ru has no page; dealer search lists only apl70_* shop pages, no TDS/SDS)
- solids %, viscosity, density — not published (aerosol, not measured by the dealer)
- dust-free time, recoat window, sanding time — only touch (10–20 min) and full dry (3–4 h) are sourced
- binder chemistry (pure acrylic vs NC-acrylic) not stated
- shelf life not published
- hardness, chemical resistance, elasticity — no figures
- consumption conflict: dealer 80–100 g/m² vs catalog 150 g/m²
- tip orifice sizes of the two supplied nozzles not published
- catalog says the tips are for 'безвоздушного' (airless) spraying, dealer/leaflet say 'безореольного' (halo-free) — likely an OCR/typo difference; dealer wording used