APL70 R9003 M
Acrylic enamel aerosol, RAL 9003 Signal White (20 gloss)
Ready-to-use acrylic enamel in a spray can, RAL 9003 Signal White, 20 gloss (semi-matt). Good hiding power, rich colour, no overspray halo, fast drying. Two caps in the box: one for halo-free blending, one for general painting.
- any wood species
- first finishing of small areas
- restoring the finish after a defect repair (chips, dents, filler)
- evening out the sheen on a repaired spot
- on-site touch-up of RAL 9003 white furniture fronts
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 R9003 M
Answers are based on the APL70 R9003 M data and the products it mixes with.
Characteristics
- Gloss
- 20 GUdealer
- Drying · Touch-dry
- 10–20 mindealer
- Drying · Full cure
- 3–4 hdealer
- Drying · Conditions
- 20 °C
- Volume
- 400 mldealer
- Pot life
- n/arecommended
- Chemistry
- 1K solvent-borne acrylic (thermoplastic/physically drying)recommended
- Chemical resistance
- lower than two-pack APL20 / APL R9003 M; alcohol and solvents can soften itrecommended
Colours
- RAL 9003 · Signal White
Application
Conventional spray
- Device
- aerosol can 400 ml (built-in valve, 2 interchangeable caps)
- Nozzle
- fixed actuator; use the halo-free (fine) cap for blending into existing finish, the standard cap for priming/whole small panelsrecommended
- Pressure · fluid
- can propellant, not adjustable (typically ~3–5 bar at 20 °C)recommended
- Pressure · air
- n/arecommended
- Spray viscosity
- factory-setrecommended
- Consumption
- 80–100 g/m²dealer
- Recoat
- next light coat after 5–10 min; past ~1 h wait for full dry (3–4 h) and scuff firstrecommended
- Sanding between coats
- usually not needed; if nibs, P800–P1000 after full dryrecommended
- Technique
- shake 1–2 min after the ball rattles; keep the can upright, start and stop off the panel, 50 % overlap; to blend into the existing finish fade the last pass out as a dry mist beyond the repairrecommended
Shake before use; don't spray on cold or hot surfaces; when finished, turn the can upside down and spray until clear to clean the valve. dealer
Process and compatibility
- Substrate preparation
- clean, dry, degreased surface; fill and flat the defect, scuff the repair edge and surrounding finish with P320–P400 (sanding sponge), de-dust; prime bare wood or filler firstrecommended
- Temperature and humidity
- 18–25 °C (can, workpiece and room), RH ≤ 70 %recommended
- Don'ts
- thin it or add hardener
- spray onto cold or hot surfaces
- lay it on in one heavy coat
- leave the valve uncleared after use
Storage
- Packaging
- 400 ml aerosol candealer
- Storage temperature
- 5–25 °C, away from heat and sun, never above 50 °Crecommended
Safety: Pressurised, highly flammable aerosol. Use with ventilation and an A-filter respirator, away from ignition sources. Don't heat above 50 °C; don't puncture or burn, even empty.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: description, uses, 80–100 g/m², 15–25 cm, notes, 20 gloss, full dry 3–4 h, 400 ml, colour RAL9003
- dealer search: full APL70 line (UM/M/SM/G white + RAL 1013/1015/9001/9003/9005/9010/9016)
- sibling APL70 SM: touch-dry 10–20 min
- sibling APL70 M: two caps in the kit
Not covered by the sources
- no official t-color.ru page or TDS/SDS found for APL70
- solids content
- viscosity (n/a in practice)
- density
- dust-free time (derived only)
- touch-dry for R9003 M itself (only sibling APL70 SM states 10–20 min)
- sanding/recoat window (derived)
- hardness, lightfastness, chemical resistance (data)
- shelf life
- resin type not stated by Technocolor (1K acrylic assumed)
- consumption conflict: dealer 80–100 g/m² vs catalog 150 g/m²
- not used in any official finishing schedule