APL70 R9001 M
Acrylic enamel aerosol, RAL 9001 Cream (20 gloss), 400 ml
Semi-matt acrylic enamel in RAL 9001 in a spray can, ready to use. Good hiding, rich colour, dries fast and leaves no overspray halo. Comes with two caps: one for halo-free spotting/touch-up and one for general painting.
- any wood species
- first finishing of small areas
- restoring the finish after a defect has been repaired (touch-up, chip repair)
- evening out the sheen over a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 R9001 M
Answers are based on the APL70 R9001 M data and the products it mixes with.
Characteristics
- Components
- 1K, ready to sprayrecommended
- Gloss
- 20 глосс (GU 60°)dealer
- Drying · Conditions
- 20 °C
- Pot life
- n/arecommended
Colours
- RAL 9001 · Cream
Application
Aerosol
- Nozzle
- use the 2 supplied actuator caps: narrow halo-free cap for spotting, wide cap for covering arearecommended
- Kit
- 2 caps: halo-free spray and general paintingcatalog
- Pressure
- n/a: pressure is fixed by the can's propellantrecommended
- Consumption (catalogue)
- 150 g/m²catalog
- Sanding between coats
- if needed, P600–P800 after full dry (3–4 h), light handrecommended
Shake the can. Hold it 15–25 cm from the surface and keep it moving; start and finish each pass off the edge of the part. Don't spray onto cold or hot surfaces. When you're done, turn the can upside down and spray until only clear gas comes out, to clean the cap.
Process and compatibility
- Substrate preparation
- Clean, dry and degreased. Scuff the old finish with P320–P400 (Scotch-Brite on profiles); fill or prime the repaired spot, sand it flush and remove all dust.recommended
- Don'ts
- don't add hardener or thinner
- don't spray onto cold or hot surfaces
- don't lay it on thick: it will run and stay soft
- don't decant it into a spray gun
Storage
- Packaging
- 400 ml aerosol candealer
- Storage temperature
- away from flame and sun, never above +50 °Crecommended
- Min order, custom tint
- custom tint to order from 24 canscatalog
Safety: Pressurised aerosol, extremely flammable. Don't heat above 50 °C; don't pierce or burn it, even when empty. Ventilate and wear an A2/P2 respirator. (Generic aerosol rules; no manufacturer SDS found.)
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: description, properties, application area, 80–100 g/m², usage notes, gloss 20, full dry 3–4 h @20 °C, 400 ml, colour RAL9001, price 821 ₽
- dealer page for the base APL70 M: same data plus 2-cap kit wording
- list of APL70 SKUs at the dealer (12 SKUs incl. R9005 M black, R1015 SM 30 gl)
Not covered by the sources
- official t-color.ru product page (none exists)
- technical data sheet / SDS PDF (none found)
- solids content
- viscosity (n/a for aerosol; can contents not specified)
- density
- dust-free and touch-dry times (only full dry 3–4 h published)
- recoat window
- hardness, lightfastness, chemical resistance, elasticity
- shelf life
- actuator cap orifice sizes / fan widths
- compatibility list (what it may go over/under)
- consumption discrepancy: catalog card 150 g/m² vs dealer 80–100 g/m²
- G gloss conflict: catalog 75 vs leaflet/dealer 70 (does not affect this M SKU)