APL70 R1015 M
Acrylic enamel aerosol, RAL 1015 light ivory (20 gloss)
Semi-matt acrylic enamel in an aerosol can for furniture and woodwork touch-up/restoration. Ready to spray, fast-drying, leaves no overspray halo, rich colour. Comes with 2 actuator tips: a halo-free blending tip and a tip for full first coats.
- Any wood species
- First finishing of small surfaces
- Restoring the finish after defect repair (chips, dents, edge repairs)
- Evening out sheen over a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 R1015 M
Answers are based on the APL70 R1015 M data and the products it mixes with.
Characteristics
- Gloss
- 20 glossdealer
- Drying · Full cure
- 3–4 hdealer
- Drying · Conditions
- 20 °C
- Ready to use
- yesdealer
- Volume (ml)
- 400dealer
- Components
- 1K (single component)recommended
Colours
- RAL 1015 · Light ivory
Application
Conventional spray
- Device
- aerosol can (400 ml), built-in propellant
- Consumption
- 80–100 g/m²dealer
- Consumption (catalogue)
- 150 g/m²catalog
- Sanding between coats
- Usually not needed; if dust nibs, light denib P600–P800 after full dry (3–4 h), then a final coat. Never sand or polish the final 20-gloss coat — it ruins the sheen.recommended
Shake the can well (1–2 min after the ball starts rattling). Test spray on cardboard. Spray from 15–25 cm in even overlapping passes, starting and stopping off the part. For spot repairs use the halo-free tip and feather out toward the edges. Don't spray onto cold or hot surfaces. When done, turn the can upside down and spray until only gas comes out to clear the tip.
Process and compatibility
- Substrate preparation
- Clean, dry, degreased surface. Level the repair (wax/filler), scuff the existing finish with P320–P400. On bare wood prime first (acrylic primer) or at least apply 2 enamel coats with a denib in between.recommended
- Temperature and humidity
- Can and workpiece at 18–25 °C, RH ≤ 70 %.recommended
- Don'ts
- Don't add hardener or thinner
- Don't spray onto cold or hot surfaces
- Don't lay on one heavy coat — it runs
- Don't sand or polish the final matt coat
Storage
- Packaging
- 400 ml aerosol candealer
- Storage temperature
- +5…+30 °C, away from heat and sun, never above 50 °Crecommended
Safety: Pressurised container: keep below 50 °C, don't pierce or burn, even when empty. Highly flammable — keep away from flames and sparks. Use with ventilation, organic-vapour respirator and gloves.
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer page: description, properties, use, 80–100 g/m², 15–25 cm, notes, 20 gloss, full dry 3–4 h at 20 °C, 400 ml, RAL1015, price
- dealer page of base white APL70 M: same description/use/80–100 g/m²/20 gloss/3–4 h/400 ml, plus '2 насадки для безореольного распыления и первичной покраски', price 632 ₽
- dealer listing of all APL70 codes (UM/M/SM/G, R1015 M/SM, R9001/R9003/R9010/R9016 M)
- dealer page of the different spray-gun product APL R1015 M (AC40 10–20 % w / 15–25 % v, S50 30–40 % w / 40–50 % v, 150 g/m², 20±3 gloss) — cited only to disambiguate
Not covered by the sources
- No official t-color.ru page or TDS/SDS for APL70 / R1015 variant
- Solids, viscosity, density not published (aerosol)
- Dust-free / touch-dry time not published (only full dry 3–4 h)
- Shelf life not published
- Hardness, chemical/light resistance not published
- Actual actuator orifice size and can pressure not published
- Consumption conflict: dealer 80–100 g/m² vs catalog family 150 g/m²
- Web search for a TDS not possible this run (session search budget exhausted); dealer + catalog re-checked 2026-10-05