APL70 R1013 M
Acrylic aerosol enamel APL70 R1013 M, RAL 1013 (20 gloss)
Satin-matt (20 gloss) acrylic enamel in an aerosol can, tinted RAL 1013. Ready to use — no thinner, no hardener. Good hiding, rich colour, fast drying, no overspray halo. Comes with two caps: a halo-free blending cap and a full-coverage cap for first coats.
- Any wood species
- First finish on small areas
- Touch-up after defect repair (chips, dents, filler)
- Matching sheen on a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 R1013 M
Answers are based on the APL70 R1013 M data and the products it mixes with.
Characteristics
- Gloss
- 20 gloss unitsdealer
- Drying · Conditions
- 20 °C
- Ready to use
- yesdealer
- Two-component
- nocatalog
Colours
- RAL 1013 · oyster white
Application
Aerosol
- Nozzle
- n/a — use the two supplied capsrecommended
- Pressure
- n/a (factory can pressure)recommended
- Consumption
- 150 g/m²
- Recoat
- wet-on-dry after 10–20 min flash; after 3–4 h full dry scuff before more coatsrecommended
- Sanding between coats
- normally none; if dust nibs, denib P800–P1000 after full dry (3–4 h)recommended
- Technique
- Short even passes, can upright, ~50 % overlap, start and stop off the part. To feather the repair edge use the halo-free cap and make the last pass from further away.recommended
Shake the can before use. Do not spray onto cold or hot surfaces. Spray from 15–25 cm. After use turn the can upside down and spray until the nozzle is clear. dealer
Process and compatibility
- Substrate preparation
- Clean, dry, degreased. Sand the repaired spot (filler/primer) P320–P400 and the surrounding old finish P600–P800 for blending. Remove dust.recommended
- Don'ts
- Do not spray on cold or hot surfaces
- Do not add hardener or thinner
- Do not lay it on heavy in one pass
- Do not polish the 20-gloss final coat
Storage
- Packaging
- 400 мл аэрозольный баллонdealer
- Storage temperature
- 5–25 °C, away from heat and sun, never above 50 °Crecommended
Safety: Pressurised, highly flammable aerosol. Do not heat above 50 °C, do not spray near flames. Use ventilation and a respirator (A2/P2 filter).
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- dealer product page: description, properties, uses, 80–100 g/m², notes, 20 gloss, full dry 3–4 h, 400 ml, RAL1013 (re-verified 2026-10-05: all values match, price 821 ₽)
- dealer APL70 M (white parent): same data, confirms family
- dealer ATL70 M sister aerosol: touch-dry 10–20 min (used for derived values)
- dealer APL R1013 M (2K gun enamel, same colour): colour name 'жемчужно-белая', confirms distinct product
Not covered by the sources
- No official t-color.ru page
- No TDS/SDS found (web search budget exhausted)
- Solids, viscosity, density not published (not meaningful for an aerosol)
- Touch-dry / dust-free time for APL70 itself (derived from ATL70 M)
- Shelf life
- Hardness, lightfastness, chemical resistance
- Consumption conflict: dealer 80–100, web catalog 60–80, 2025 catalog transcript 150 g/m²
- Not used in any official finishing schedule
- G-variant gloss conflict 70 vs 75 gl between catalogs (not this SKU)