APL70 G
White acrylic enamel, gloss (70 GU), 400 ml aerosol can
Acrylic enamel in a spray can for repair/touch-up work: high hiding, rich colour, fast drying. Ready to use. Comes with 2 actuator caps — one for halo-free blending, one for straight painting.
- Any wood species
- Finishing small areas
- Restoring the finish after a repair
- Matching sheen on a repaired spot
Single-component product: no mixing needed — use as supplied (see application below).
Ask about APL70 G
Answers are based on the APL70 G data and the products it mixes with.
Characteristics
- Gloss
- 70 GU 60°dealer
- Drying · Touch-dry
- 10–20dealer
- Drying · Full cure
- 3–4dealer
- Drying · Conditions
- 20 °C
- Volume
- 400 mldealer
- Components
- 1K, ready to usecatalog
Colours
- белый · White
Application
Aerosol
- Method (fallback)
- conventional_spray
- Consumption
- 80–100dealer
- Gun distance
- 15–25dealer
- Nozzle
- not adjustable — 2 supplied actuators (halo-free for blending, standard for straight coverage)recommended
- Pressure
- не регулируется (давление баллона) / not adjustable (can pressure); греть баллон до комнатной температуры ~20 °C / bring the can to room temperature ~20 °Crecommended
- Sanding between coats
- do not sand between coats; for dust nibs wait 3–4 h and denib at P800–P1000recommended
- Technique
- Keep the can upright, move at an even pace, start and stop the spray off the part, ~50 % overlap. To blend into old finish use the halo-free cap and a light misting last pass over the edge.recommended
Shake the can before use. Don't spray onto cold or hot surfaces. Spray from 15–25 cm. After use, turn the can upside down and spray until the nozzle runs clear. dealer
Process and compatibility
- Substrate preparation
- Fill/repair the spot, sand P320–P400, key the surrounding old finish with P600–P800 or a grey pad, de-dust and degrease. Seal bare wood with a primer first.recommended
- Sanding
- don't sand or polish the final gloss coat unless you mustrecommended
- Don'ts
- Don't spray onto cold or hot surfaces
- Don't skip shaking the can
- Don't put the can away without clearing the nozzle
Storage
- Packaging
- 400 ml aerosol can + 2 capsdealer
Sources
Value tags: “official”, “dealer”, “catalog”, “schedule” are Technocolor data; “workshop” is from our own datasheets; “recommended” is our engineering estimate (hover to see the reasoning).
- описание, свойства, применение, расход 80–100 г/м², дистанция 15–25 см, блеск 70, полная сушка 3–4 ч, 400 мл, цвет белый
- сестринская APL70 SM: на ощупь 10–20 мин
- состав линейки APL70 (UM/M/SM/G + RAL-цвета)
- APL70 R1013 M, APL70 R9005 M
Not covered by the sources
- solids_pct (не опубликовано)
- viscosity (не применимо к аэрозолю / not published)
- density
- dust_free_min и touch_min для APL70 G (touch 10–20 мин взято у APL70 SM)
- stack_or_sand_h
- hardness, lightfastness, chemical_resistance, elasticity
- shelf_life
- wet_film_um
- official SDS/TDS не найден (у дилера и на t-color.ru нет)
- расхождение блеска 70 vs 75 гл (каталог 2025) не разрешено